|
- informs the user about the following  ‘health’ parameters:
| • | temperatures |
| • | voltages |
| • | State of fans |
health dialog:
With this dialog the reason for a alarm can be investigated. Items which are not checked cause a alarm.
With the information shown in this dialog, you can investigate the cause of any alarm.
Any items which are not ‘checked’ will be the cause!
Note 1:
The values (and tolerances) given below are true for most codecs. Nevertheless, there are exceptions. If you encounter any discrepancy, please contact your local Dealer directly, or Mayah Communications via support@mayah.com.
Note 2:
The Fallback temperature is the temperature which de-activates an existing alarm.
Note 3:
In case of a permanent alarm, please contact your local Dealer or Mayah Communications directly via support@mayah.com.
Items:
| • | Motherboard and CPU Performance:
Possible values:
- NMC board: AMD K6II (400 and 500 MHz)
- Epox board: AMD K6II (400 and 500 MHz)
- TYAN board: AMD Duron (800 MHz) and AMD Duron (1000 MHz)
- Shuttle board: Celeron (1100 and 1200 MHz)
- SOYO board: Celeron (1100 and 1200 MHz)
- VIA board: Celeron (1100, 1200 and 1300 MHz)
- DFI board: Celeron (1200 and 1300 MHz) or Pentium III (1400 MHz) |
| • | Memory:
Possible values:
- 32 MB
- 128 MB |
| • | System Disk:
- indicates the capacity of the system partition of the internal Flash card. The system partition is assigned to Drive C. |
| • | System Disk Free:
- indicates the amount of available space on the System partition of the Flash card. If this is less than 500kB, a alarm is raised. |
| • | User Disk:
- indicates the capacity of the User partition of the internal Flash card. The user partition is assigned to Drive D. |
| • | User Disk Free:
- indicates the amount of available space remaining on the User partition of the Flash card. If this is less than 2 MB, an alarm is raised. |
| • | CPU Temperature:
If this value is outside its tolerance, it causes an alarm to be raised.
CPU temperature tolerances:
- AMDK6II: 70°C (fall back 65°C)
- AMD Duron (800 MHz): 90°C (fall back 85°C)
- AMD Duron 1000 MHz: 90°C (fall back 85°C)
- Intel Celeron (1100-1300 MHz): 69°C (fall back 64°C)
- Intel Pentium III (1400 MHz): 69°C (fall back 64°C) |
| • | System temperature:
If the value is outside its tolerance range, it causes an alarm to be raised.
System temperature tolerances:
- AMDK6II: 55°C (fall back 50°C)
- AMD Duron 800 MHz: 60°C (fall back 55°C)
- AMD Duron 1000 MHz: 60°C (fall back 55°C)
- Intel Celeron (1100-1300 MHz): 60°C (fall back 55°C)
- Intel Pentium III (1400 MHz): 60°C (fall back 55°C) |
| • | CPU Core Voltage:
If the value is outside its tolerance range, it causes an alarm to be raised.
CPU core voltage tolerances:
- AMDK6II: min.: 2.1V, max.: 2.3V
- AMD Duron 800 MHz: min.: 1.5V, max.: 1.7V
- AMD Duron 1000 MHz: min.: 1.7V, max.: 1.8V
- Intel Celeron (1100-1300 MHz): min.: 1.4V, max.: 1.55V
- Intel Pentium III (1400 MHz): min.: 1.4V, max.: 1.55V |
| • | 3.3Volt Voltage:
If the value is outside its tolerance range, it causes an alarm to be raised.
3.3V voltage tolerances:
- NMC-board: min.: 3.135V, max.: 3.465V
- Epox-board: min.: 3.135V, max.: 3.465V
- TYAN-board: min.: 3.135V, max.: 3.565V
- Shuttle-board: min.: 3.135V, max.: 3.565V
- SOYO-board: min.: 3.135V, max.: 3.565V
- VIA-board: min.: 3.135V, max.: 3.465V
- DFI-board: min.: 3.135V, max.: 3.465V |
| • | 5Volt Voltage:
If the value is outside its tolerance range, it causes an alarm to be raised.
5V voltage tolerances:
- NMC-board: min.: 4.6V, max.: 5.25V
- Epox-board: min.: 4.6V, max.: 5.25V
- TYAN-board: min.: 4.6V, max.: 5.25V
- Shuttle-board: min.: 4.6V, max.: 5.25V
- SOYO-board: min.: 4.6V, max.: 5.25V
- VIA-board: min.: 4.6V, max.: 5.25V
- DFI-board: min.: 4.6V, max.: 5.25V |
| • | 12Volt Voltage:
If the value is outside its tolerance range, it causes an alarm to be raised.
12V voltage tolerances:
- NMC-board: min.: 9V, max.: 14V
- Epox-board: min.: 9V, max.: 14V
- TYAN-board: min.: 9V, max.: 14V
- Shuttle-board: min.: 9V, max.: 14V
- SOYO-board: min.: 9V, max.: 14V
- VIA-board: min.: 9V, max.: 14V
- DFI-board: min.: 9V, max.: 14V |
| • | Minus12Volt Voltage:
If the value is outside its tolerance range, it causes an alarm to be raised.
-12V voltage tolerances:
- NMC-board: min.: -14V, max.: -9V
- Epox-board: min.: -14V, max.: -9V
- TYAN-board: min.: -14V, max.: -9V
- Shuttle-board: min.: -14V, max.: -9V
- SOYO-board: min.: -14V, max.: -9V
- VIA-board: min.: -14V, max.: -9V
- DFI-board: min.: -14V, max.: -9V |
| • | CPU Fan:
If the revs of the CPU fan runs slower than 3,500 RPM, it will generate an alarm. |
| • | Chassis Fan:
If the revs of the Chassis fan runs slower than 3,500 RPM, it will generate an alarm. |
Note:
The Parameters (and values) shown in this dialog cannot be changed.
|
Health